A pool filter is one of the most vital parts of a pool system. The absence of a filter or poor pool filtering system will not only cause havoc to your entire pool but also affects your personal hygiene.
Without a pool filter, debris and dirt will not only find their way to your pool, but they will also remain there for an extended period. Most algae growth in your pools comes from a bad pool filter, and when you fail to get this fixed, the water becomes clouded and unhygienic for use.
It’s no news that pool filters could develop faults over time due to wear, but regular maintenance will keep your filter working for years.
The Hayward pool filter is no exception to defect, just like every other filter. One of the most common issues you may experience with this pool filter is leakage, which occurs at the top of the filter. However, with little technical skills needed, simple hand tools could be all it requires to get it done.
Here in this article, you will learn the major causes of your pool filter leakage from the top and how to get that fixed.
Why Your Hayward Pool Filter Leaks from the Top
Like earlier said, there are several reasons why your Hayward filter is leaking from the top. When you experience leakage from the top of the filter, the first thing to check is the O-ring that seals the top half of the filter to the bottom filter.
This could be that the silicone lube had worn-out or must have been pinched when you were trying to replace the lid cover. If that’s the case, get a fresh silicone lube to reapply.
Also, faulty gasket, cracks, loose nuts, and bolt could be a possible reason you experience pool filter lid leaking.
In case of a cracked tank, you might want to purchase a new filter, especially if you are using a san filter. If you have a faulty gasket that causes a leak from the multiport valve or backwash line, try to adjust the gasket. If that doesn’t fix it, replace the entire gasket.
Another reason why your pool filter will leak from the top could be that you have a worn-out Hayward filter clamp. This happens majorly on sand filters and can be easily replaced.
How to Fix O-ring in Hayward Pool Filter
A faulty O-ring is the major cause of leaks in pool filters. It affects the proper filtration of water. Fixing an O-ring requires sealing the lid cover’s edges to ensure its airtight when pressure is applied.
Here are the steps to doing that:
Step 1: Power off the pump from the source electricity supply.
Step 2: Slowly turn the pressure valve in an anticlockwise direction until the water drips down from the valve. At this point, observe the pressure gauge until it drops to zero.
Step 3: Slowly open the locking knob by rotating in an anticlockwise direction and keep the filter head away from the body.
Step 4: Face the head of the filter downward, and you would see the O-ring sitting on the groove. Gently push the O-ring upward from the groove and clean the groove with a damp cloth.
Step 5: Fix the new O-ring to the groove and seal the O-ring with a silicone lube.
Step 6: Place the head of the filter to the body so the pressure gauge faces outside. Check again to be sure the O-ring is sitting properly on the groove.
Step 7: Lock the head of the filter to the body and power on the filter when everything is set.
Step 8: Crosscheck the pressure if it has returned to normal.
What Happens When Hayward Pool Filter Is Leaking
A pool filter is like the kidney of your pool. The best thing to do for your pool is to monitor the filter and make sure everything is working fine.
Many things can occur when your pool filter isn’t working as expected. Such could create room for algae or bacteria growth, which is not hygienic for you.
Filter leaks have been one of the major issues for pool owners, in as much as it doesn’t cause a significant low water level. Still, it is necessary to be monitored and fixed to avoid other damages.
A leak in your filter can also cause an imbalance in the filter pressure. Low and high filter pressure is a problem caused when water is obstructed while going to the filter.
This can impact water circulation. Low pressure can be caused by having too little water level or too little sand in the pool filter.
High pressure can be caused by having too much sand in the pool filter or having a filter that is smaller than the pump.
So when there is a leak in the filter, the pressure gauge will give wrong readings, and when the pool sand filter pressure is too high, it could crack the lateral and allow sand to leak into the pool.
Conclusion
A leaking pool filter is the major cause of poor filtration in pools. If that needs to be addressed, you would regularly need to monitor the filter and other pool units for a purer and cleaner facility.